ABOUT INDEXING EDITORIAL BOARD ARCHIVES AUTHOR GUIDELINES SUBMIT PAPER NEWS, EVENTS AUTHOR'S PAGE CONTACT
Materiale Plastice
Cite as: Mater. Plast.
https://doi.org/10.37358/Mat.Plast.1964

OSIM Nr. R102356
ISSN Print 0025-5289
ISSN Online 2668-8220
Materiale Plastice - Latest Issue

Latest Issue >>>
ARCHIVES
   Volume 59, 2022
   Volume 58, 2021
   Volume 57, 2020
   Volume 56, 2019
   Volume 55, 2018
   Volume 54, 2017
   Volume 53, 2016
   Volume 52, 2015
   Volume 51, 2014
   Volume 50, 2013
   Volume 49, 2012
   Volume 48, 2011
   Volume 47, 2010
   Volume 46, 2009
   Volume 45, 2008
   Volume 44, 2007
   Volume 43, 2006
   Volume 42, 2005
   Volume 41, 2004
   Volume 40, 2003
 
<<<< back

Materiale Plastice (Mater. Plast.), Year 2022, Volume 59, Issue 3, 245-257

https://doi.org/10.37358/MP.22.3.5618

Mircea Dorin Vasilescu

Preliminary Technological and Environmental Considerations for Generating Mechanical Components using Plant-based UV Resin


Abstract:
The scope of this paper is to determine the evolution of the dimensional value of the part and to study if there is gas and particle emission produced by the plant-based resin in the 3D printing process with mask stereolithography. For dimensional measurement, a solution with digital calliper is used. For the measurement of emission, two devices are used for indoor air quality. In the vertical direction of part body printed, it is possible to observe a descending linear type of direction with a minimum value at the highest element 3D printed. The data taken into account in this study are mathematically studied using the EXCEL regression equation for dimension. The gases emitted are measured with the booth devices in parallel for formaldehyde and volatile organic compound gases. For CO2 and particles, one of these devices is used. The air quality index was determined in relation to CO2 and, respectively, particle emitted. In the printing process, an increase in CO2 emission of 500 ppm can be observed in the initial phase of the process and a lower value in the body area. It is possible to consider that the quality air in 3D printing with plant-based clear resin is in the good to medium level from all types of emission. These data were put in ac-cordance with the level value offered by the manufacturer of the measuring devices. In this study the dimensional aspects are evaluated in parallel for two types of part bodies and the dimensional equations are the same after three mount times.


Keywords:
biomaterials; sensors for gas or particle; 3D printing; polymer processingword 3

Issue: 2022 Volume 59, Issue 3
Pages: 245-257
Publication date: 2022/10/3
https://doi.org/10.37358/MP.22.3.5618
download pdf   Download Pdf Article
Creative Commons License
This article is published under the Creative Commons Attribution 4.0 International License
Citation Styles
Cite this article as:
VASILESCU, M.D., , Preliminary Technological and Environmental Considerations for Generating Mechanical Components using Plant-based UV Resin, Mater. Plast., 59(3), 2022, 245-257. https://doi.org/10.37358/MP.22.3.5618

Vancouver
Vasilescu MD. Preliminary Technological and Environmental Considerations for Generating Mechanical Components using Plant-based UV Resin. Mater. Plast.[internet]. 2022 Jul;59(3):245-257. Available from: https://doi.org/10.37358/MP.22.3.5618


APA 6th edition
Vasilescu, M.D., (2022). Preliminary Technological and Environmental Considerations for Generating Mechanical Components using Plant-based UV Resin. Materiale Plastice, 59(3), 245-257. https://doi.org/10.37358/MP.22.3.5618


Harvard
Vasilescu, M.D., (2022). 'Preliminary Technological and Environmental Considerations for Generating Mechanical Components using Plant-based UV Resin', Materiale Plastice, 59(3), pp. 245-257. https://doi.org/10.37358/MP.22.3.5618


IEEE
M.D. Vasilescu, "Preliminary Technological and Environmental Considerations for Generating Mechanical Components using Plant-based UV Resin". Materiale Plastice, vol. 59, no. 3, pp. 245-257, 2022. [online]. https://doi.org/10.37358/MP.22.3.5618


Text
Mircea Dorin Vasilescu,
Preliminary Technological and Environmental Considerations for Generating Mechanical Components using Plant-based UV Resin,
Materiale Plastice,
Volume 59, Issue 3,
2022,
Pages 245-257,
ISSN 2668-8220,
https://doi.org/10.37358/MP.22.3.5618.
(https://revmaterialeplastice.ro/Articles.asp?ID=5618)
Keywords: biomaterials; sensors for gas or particle; 3D printing; polymer processingword 3


RIS
TY - JOUR
T1 - Preliminary Technological and Environmental Considerations for Generating Mechanical Components using Plant-based UV Resin
A1 - Vasilescu, Mircea Dorin
JF - Materiale Plastice
JO - Mater. Plast.
PB - Materiale Plastice SRL
SN - 2668-8220
Y1 - 2022
VL - 59
IS - 3
SP - 245
EP - 257
UR - https://doi.org/10.37358/MP.22.3.5618
KW - biomaterials; sensors for gas or particle
KW - 3D printing
KW - polymer processingword 3
ER -


BibTex
@article{MatPlast2022P245,
author = {Vasilescu Mircea Dorin},
title = {Preliminary Technological and Environmental Considerations for Generating Mechanical Components using Plant-based UV Resin},
journal = {Materiale Plastice},
volume = {59},
number = {3},
pages = {245-257},
year = {2022},
issn = {2668-8220},
doi = {https://doi.org/10.37358/MP.22.3.5618},
url = {https://revmaterialeplastice.ro/Articles.asp?ID=5618}
}


Download article Citations:
 PlainText citation Plain Text
 Text citation Text
 GoogleScholar citation Google Scholar


Downloads number: 6
<<<< back
 
  Search Authors
Crossref Member Badge
 DOI  logo
 Gold Open Access | Source=http://www.plos.org/  | Author=art designer at PLoS
Creative Commons License